How-to-Build-a-Backyard-Wooden-Balance-Beam

How to Build a Backyard Wooden Balance Beam

Build a backyard wooden balance beam for your kids are good for practicing children’s balance. Of course, anything for children can be purchased, and a balancing beam cannot be overlooked, but what if the balance beam is created by the children themselves? Then it’s no longer about the little ballerina’s balancing performance, but the playfulness is still present.

When tiny children are allowed to participate in the creation of the balance beam and may later claim, “I constructed this with my dad or my mom,” it becomes a game for them. The balance beam gains an entirely new status, and the neighboring children are overjoyed.

The Thought of Build a Backyard Wooden Balance Beam

How-to-Build-a-Backyard-Wooden-Balance-Beam

Mothers frequently observe their children having a great time balancing on a playground beam. So, what could be more natural than constructing your own balance beam for the garden?

As a result, the initial route for the merchandise led to the hardware store, where everything was purchased. What you eventually need for it is kept to a minimum, and the cost remains under 50 euros.

What Hardware Store Components Were Purchased for the Balancing Beam?

  • 1 wooden beam with the dimensions: 100×100 and a length of 1800 mm
  • suitable screws
  • sandpaper for machine or hand sanding
  • spray paint 2x white, 1x pink/pink 1x clear varnish
  • a short wooden beam
  • masking tape for masking
  • 1 saw for cutting
  • 1 folding rule
  • 1 angle
  • Wood glue (safer in the long run)
  • drill
  • Drill (wood drill)
  • screw clamps
  • plane
✅ READ :   Tutorial on How to Make a Tire Swing for Backyard Playground

The first step is to create a drawing of the balancing beam. All dimensions, including wood thickness, are entered in this drawing because the screw length is based on this. It doesn’t hurt to pre-drill the screw holes in larch wood. Drill a short hole at the top with a countersink or an 8–10 mm drill bit so the screws can be countersunk flush in the wood. There can be no harm done in this manner.

Step by step, construction can now begin.

Stand Balancing Beam Substructures

The first step is to measure the larch wood with a length of 1800 mm, which will later act as a balancing pole to prevent the children from injuring themselves and falling down.

The actual substructure was quite simple: two stronger short beams at the bottom, screwed on each side with two boards, but still quite wobbly and needed to be reinforced.

Two surplus beams from timber functioned as floor boards for this project. These were chopped to size. Furthermore, lark wood should be used to form four triangles to fasten the side portions.

Cut two rectangles out of the foundation plate sections and put them between the two side pieces to make them stronger.

The balancing beam is now being assembled.

First, the feet are screwed together and clamped together. Pre-drill the entire program using Spax screws (5×70 mm) before screwing it together. Pre-drilling is critical; otherwise, the screw may not sit entirely in the wood (risk of injury). The feet are now secured from beneath. This is best done using carriage bolts measuring 6×100 mm (screws with a round head and 6 mm thread). Pre-drill and drill a recess with a countersink or an 18 mm drill bit to ensure that the carriage bolt heads are flush with the wood. Simply screw it in and you’re finished.

✅ READ :   How To Build a Backyard Climbing Rock Wall For Kids In 8 Steps

The substance may still be unstable, depending on the thickness of the wood. The difficulty can be rectified by adding an extension to the base plates. To do this, ordinary wood must be cut to 900 mm in length and furnished with a bevel cut at the ends to prevent the children from injuring themselves.

The edges can then be made even finer on the spot.

The Final Assembly

All of the balance beam’s components have been assembled, labelled, and drilled with an 18 mm drill. Drill another little hole with the 5 mm wood to fit the 8 x 50 mm screws gallantly.

The Supporting Beam for Wooden Balance Beam

This is an unplaned 100x100x1800 mm larch post that will need to be handled. The planer is used to shape the unplaned balance beam. An electric planer is ideal for processing the surfaces, while a hand planer is used to complete the edges.

It is recommended to round off the ends for safety reasons. The jigsaw (long saw blade) is used to cut off the curves.Now, sand everything thoroughly and proceed.

A little stairwell

A tiny stairway can be quite useful in allowing the children to bravely gain a grip on the balance beam. It’s time to return to the toolbox and chop some scrap wood.

Because the beam isn’t very high, two steps are plenty. So the wood merely needs to be sawed to size and assembled. A little adhesive on top of the screws isn’t going to hurt.

The Final Assembly

Just put everything together and test it for safety. The substructure is built first, and then the balancing beam is installed. Screw clamps are used to hold everything together, and an 18 mm drill bit is used to pre-drill the holes at the base. The screws are 80×50 mm and are quite durable. The staircase is screwed into place at the end of the procedure. The floor’s feet should be coated with a moisture-resistant paint.

✅ READ :   How to Create the Ideal Musical Garden

Because it is a shell, the spray can colors listed above were chosen. Of course, any other hue is an option. The color selection should be left to the children.

The colors must dry thoroughly for the balancing beam to last and not lose its face for an extended period of time. The drying time on the imprint can be obtained from the spray container. The second clear coat should be applied from a regular can rather than a spray can. The longer the balance bar shines in its color scheme, the better the clear coat application.

Conclusion

The creation of a balance beam is frequently done with a mother and child as a daily chore. The structure itself is modest and unremarkable, and it does not place too many expectations on the family. Nonetheless, some talent is required, which not all women can claim in the DIY field.

The balance beam does not need to be carpentered in piecework, and if a piece of wood has already been sawed, a fresh piece of wood is simply sawed. Finally, it will be a lovely balance beam to the delight of the children.

I hope you found my tutorial on how to build a backyard wooden balance beam useful. If you need more inspiration for building a beautiful and interesting playground for your children, go no further than these backyard playground ideas. Also read how to build a backyard climbing rock wall for kids in 8 steps.